(20)1/2" TEE SHARKBITE STYLE PUSH FIT COPPER PEX CPVC Push'N'Connect LEAD FREE

Description

(20) 1/2" TEE SHARKBITE STYLE PUSH FIT COPPER PEX CPVC TEE
(20) 1/2" TEE SHARKBITE STYLE PUSH FIT COPPER PEX CPVC TEE Push'N'Connect LEAD FREE
Push to Connect (Push-Fit) Coupling is intended to connect two CTS pipes together in a straight line.
For use with 1/2" CTS (7/8” OD) PEX, copper, CPVC and PE-RT pipes.
Lead-free DZR (dezincification resistant) brass, approved for potable water use nationwide.
NSF/ANSI 14, 61 & 372, ASSE 1061 listed.
cUPC (Uniform Plumbing Code) listed.
Rated up to 100 psi at 180°F for continuous use.
(2) PEX insert/stiffeners included.
Replaces SharkBite, TecTite, ProBite and other push fitting brands.
Advantages of push fittings:
No crimp/clamp/soldering tools required.
No crimp rings or clamps required.
No need to gauge connections for accuracy.
No soldering needed (and no open flame).
No gluing.
Easily transition between PEX, copper and CPVC.
Faster and easier than any common connection method.
Installation with PEX tubing:
Make a clean and square cut using a plastic pipe cutter.
Mark insertion depth using U702 tool or measuring tape (see chart below).
Fully insert pipe into the fitting and check the insertion depth.
Installation with Copper pipe:
Cut the pipe using a standard copper pipe cutter (do not use hacksaw or band saw).
Ream the outside and inside of the copper pipe to smooth out its edge (use U702 or similar tool).
Mark insertion depth using
DT1234
or measuring tape (see chart below).
Remove the PEX insert from the fitting using a
CDT12
or
CDT34
and needlenose pliers.
Fully insert pipe into the fitting and check the insertion depth.
Installation with CPVC pipe:
Cut the pipe using a standard pipe cutter. If using a hacksaw – ream the pipe’s edges.
Mark insertion depth using
DT1234
tool or measuring tape (see chart below).
Remove the PEX insert from the fitting using a disconnect clip and needlenose pliers.
Fully insert pipe into the fitting and check the insertion depth.
Pipe insertion depth chart:
Pipe Size (CTS/Nominal)
Pipe Size (OD)
Insertion Depth
1/4"
3/8"
13/16"
3/8"
1/2"
15/16"
1/2"
5/8"
15/16"
3/4"
7/8"
1-1/8"
1"
1-1/8"
1-5/16"
To disconnect:
Use disconnect clip of size corresponding to CTS pipe size. Snap the clip over the pipe near the fitting and push it down on the innermost collar of the fitting (which comes in contact with the pipe), while simultaneously pulling the pipe and fitting apart.
DO’s:
Always pressure test the system after installation
Cut the pipe gradually. With copper pipe especially, excessive force may deform otherwise round pipe shape.
If using with copper pipe, reaming is a must – it will prevent damage to the O-ring from abrasive edges.
PEX insert is required when installing the fitting on a PEX pipe.
DONT’s:
Do not sand the pipe or apply any kind of glue or sealing tape.
Do not install in glycol containing systems (i.e. snow/ice melting systems).
Do not re-use fittings on different connections.
Do not use on soft and rolled copper – only hard drawn standard K, L, M copper pipes.
Note: push fittings are not compatible with PEX-AL-PEX, PB (PolyButylene), PVC pipes and cannot be used for air/gas/oil applications.
Buyer pays shipping and handling price as shown in eBay's Shipping & Payment detail section.
Some items we ship to US only, some of them to US, Canada and Worldwide. The larger items can be shipped to Canada and Worldwide (see info at the top of the listing for 'Ships to' locations).
Item will be shipped to the shipping address you provide during checkout. If you wish to ship to a different address you must contact us by email right after making your payment (10 minutes).
Items are normally shipped the same or next business day after receiving cleared payment (normally M-F except holidays).
If paying by PayPal eCheck, we will ship as soon as funds clear the account.
The estimated delivery date shown above is only an estimate inserted by eBay based on shipping methods. These are not guaranteed. We can not guarantee you will receive the item by that date, we can only guarantee that we will ship quickly. After that it is in the hands of the US Postal Service.
US Addresses - Our Standard Flat Rate Shipping is normally by USPS Priority Mail (or 1st Class mail). We may also use FedEx for larger items at our discretion.
Canada and Worldwide - We offer USPS First Class Mail International and Priority Mail International.
Tracking is not available for abroad USPS First Class Mail shipments. We can provide only customs number for USPS First Class International. Please keep in mind that USPS First Class Mail can take several weeks to arrive.
Packaging - some items may have their display removed and discarded for ease of shipping.
Also we may remove an item from its original box/package and ship it in a new box/envelope (also for ease of shipping or to improve packaging).
We accept PayPal only.
We no reserve the items if payment is not received right after the auction ended.
No local pick up service.
Sales taxes would be charged for items shipped to NY (8.875%).
Return Policy
If defective upon receipt, please contact us by email within 14 days for refund or replacement arrangements.
If you do not like the item, you may return it and we will refund the purchase price (shipping & handling is not refundable).
The item must be returned in new condition within 14 days for a refund.
Buyer pays return shipping costs.
International Buyers - Please Note
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying.
These charges are normally collected by the delivering freight (shipping) company or when you pick the item up. Please, do not confuse them for additional shipping charges.